1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Fences

Discussion in 'Airport Design Editor' started by Reider, 28/1/08.

  1. Reider

    Reider

    Joined:
    6/12/07
    Messages:
    76
    My learning continues, did some more work on my EGCB Manchester Barton airfield yesterday....taking a break from my GPS carrier. Managed to pick 4 selected buildings from 8 and exclude them, only the present fuel pump to go, to be replaced with one that represents the real world version a bit more closely. :)

    I worked on the present perimeter fence too as this fitted the bill but had no opening near my added road, connecting to the dual carriageway outside. I could not seem to amend the original so I constructed an identical one that ended with a gap at the right place, this I put together as close to the original as I could and following all the contours. Then deleted the original and moved the new one closer in. A few views in FSX and ADE, tiny adjustments and the deed was done at 2.30am. ;)

    I realize that only two of the GUIDs` work from the fences but need to put in a small wooden picket fence preferably in a dual line with a pavement between as a walkway. Hoping to see one on an airfield so I can borrow it. Unless anyone has any other ideas about this one? I know I have one somewhere but also looking for an hanger with an open door, only I`d like to have a microlight on show in the opening instead of the usual plane that we always see-again, any ideas are useful. This has to be a tall hanger, in keeping with real life. The size of the current one is about right but needs the open door and microlight showing, though I might just have to make it a light plane, since they are both housed in there.

    Reider
    ________
    BMW R1100S
    Last edited: 20/1/11
  2. jvile

    jvile

    Joined:
    24/1/05
    Messages:
    7,614
    Here are some Generic wood, brick and rock fences that come with FSX.

    gen_fencewhitelong01
    {0336972F-D690-4C3D-B97F-45DA2029D29B}
    size: 428.37, 2.02, 0.00

    gen_fencewood01
    {5459DECD-B693-4CA8-866D-ABB4D119CDEA}
    size: 5.33, 1.41, 1.59

    gen_wallbrickpillar01
    {99CB8A79-0729-4784-9722-5FE4FC6785CC}
    size: 0.52, 3.06, 0.53

    gen_wallbricksmall01
    {9159B87C-54D1-4A21-8822-AB6B7EFC6D1F}
    size: 0.40, 2.82, 11.37

    gen_wallbricklarge01
    {FF9AC16F-4125-483B-9BDA-FEB787E5A3A0}
    size: 1.98, 4.14, 11.37

    gen_wallrock01
    {BEE8035B-5AB4-40BC-825D-8978E6A9296E}
    size: 10.00, 2.00, 0.43

    FSX also has several different type Generic hangers with open doors.
  3. Reider

    Reider

    Joined:
    6/12/07
    Messages:
    76
    Thanks Jim, learning more and more as I go along. Got rid of the old fuel pump and trigger now. I got my parking area fence in after a few attempts, it separates the grass of the aircraft parking and runways from the general public. Its a weird shape but after some manipulation its blended in quite well.

    Next I`ll look at a suitable xml file to replace the temporary parking fence (same as the perimeter fence) with the wooden one from your list. Much appreciated.....

    Reider
    ________
    vaporizers
    Last edited: 20/1/11
  4. Timmo

    Timmo

    Joined:
    10/1/07
    Messages:
    547
    Country:
    newzealand
    Some of those default fences have wierd alpha channels on the textures so they dont look good at all....try em and see though
  5. jvile

    jvile

    Joined:
    24/1/05
    Messages:
    7,614
    Timmo

    I did not list the ones that have the bad alpha channels.

    FSX screwed those up real good and it is ashame because those are actually better then the ones they got right.

Share This Page