Have airport near the high mountain at end of RW 36.
So need AI to always take-off from RW 18 away from mountain (avoiding the mountain while climbing) and land on RW 36 towards the mountain (avoiding the mountain during landing). Preferably regardless the wind direction.
I am aware that I...
have downloaded add-on airport. Looks great but no AI.
I opened the airport from bgl and added the necessary links, start locations, holds … and so on to make the airport available for AI.
After the compile and after I removed the original airport bgl the AI operates great.
Is there any trick to see the runway lights during the day time. I just enhanced an airport with runway lightning and the lights are only seen during night. I need to show these when landing
during the day time also (fog or low clouds).
Purchased some nice water Cessna's from HTAI and created water airport using AFCAD. As from my experience and as suggested have made all the links and runway 'concrete' 1ft wide. Aircraft take off and land great with no problems. See the picture.
THEN, I opened the airport in ADE (wanted to...
I noted (while working many years) at JFK that most of the 13L/R approaches are over VOR Canarsie. Or approaching JFK heading roughly 45 over Canarsie VOR and turning sharp right to land either 13L or 13R. Unfortunately the stock JFK has 13L ILS and basically ATC route all AI aircraft to...
Have used ADE to enhance PRG airport - (in stock only two runways 24/6 and 31/13). But I also opened existing 22/4 (closed in the stock version) and made it parallel with 24/6. So depending on the wind direction the landings/takeoffs are either on 31/13 or on both 24/6 and 22/4. Works great...
Have asked this in a different forum but thought that someone here might have an idea why I have below problem:
Fore some unknown reason when I select Pennsylvania in the State/Province dropdown, the list of the previously selected state cities stays there and the PA cities/airports do not...
have just upgraded to W10 and got FS2004 running successfully on it. On my Vista PC I was able to minimize FS by pressing the Windows key while ADE was opened and alternate between FS and ADE when designing the airport (seeing aircraft as red x in ADE then switching to FS to move aircraft to...
Hi there, just got new W10 PC and loaded FS2004 on it. Works great and obviously my next step was to get ADE. It loaded OK, I can Open airports from bgl and from my previously created airport files BUT cannot open the stock airport? Probably some triviality.
I can select it from the list, it...
Hi there, just got new W10 PC and loaded FS2004 on it. Works great and obviously my next step was to get ADE. It loaded OK, I can Open airports from bgl and from my previously created airport files BUT cannot open the stock airport? Probably some triviality. I can select it from the list, it...
Got some nice AI Helicopters and have designed airports with gates and short runways for these to take off and land, works great.
BUT understand that the choppers can also take off from helipads with start locations there. Could you please give me a brief instruction on how to use the...
Got some nice vintage sea aircraft and created airport at the beach in the water (close to Nantucket in Atlantic ocean). The aircraft show OK but after getting clearance from the tower, instead of taxiing to end of the runway, the aircraft disappear. The airport is created correctly with all...
This never happened to me before..did some mods in stock KCMI airport and when connecting the links, either to parking spots or runways the links snapped to different parts of the airport extending in different directions. The simple taxi or apron links instead of connecting to the point I...
Tried to do extended compile, just needed approach bgl and got error message. Attached.
Have searched for answer, maybe not enough, so appologies if answered elswhere.
In either case any help would be appreciated.
Just curious about engine smoke. It can be entered in aircraft.config file under [LIGHTS] or under [SMOKESYSTEM]. I have many aircraft with engine smoke under LIGHTS and it works fine for AI, but just have seen instruction to enter engine smoke under SMOKESYSTEM, with applicable gauge. How...
I know there is a keyboard shortcut to add position markers from Flight Simulator while both FS and ADE are opened (obviously got FSUIPC). Could you please let me know what the shortcut is - I recall it was a tab? and something else???