• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

FSX Partial Gear Animation

Messages
292
Country
unitedkingdom
My landing gear animation for all wheels is only partially working, the extension & retraction works OK but the compression animation is not, the gear is in the fully compressed position all the time.

My KF's are 0-100 gear extension/retraction, 100-200 gear compression. All animations are linear & I have checked that they are correctly tagged in the animation manager.

Appreciate any help with this.

Paul
 
Last edited:
I had a look at the tutorial & calculated the relevant data I needed to enter in the contact points section, however this made no difference, having thought about this, it occurred to me that there should be some movement even if the wrong data in the contact points section had been entered, the gear is in the fully compressed position in all situations, why is it in the fully compressed position & not the fully extended position which is KF 100 when the fully compressed position is at KF 200?

Paul
 
Yes, KF100 Fully Extended, KF150 Static Compression & KF200 Full Compression, I tried it with only KF100 Fully Extended, & KF200 Full Compression animated but made no difference.

Paul
 
Did you assign an animation length from 0 to 200 keyframes in Animation Manager?

FSX will only play a 200 keyframe animation to frame 100 if you put "start" and "end" to keyframe 0 and 100 respectively.
 
I assigned the gear retraction parts to start at "0" & end at "100" (which are working OK in FSX) & the gear compression parts to start at "100" & end at "200" in the Animation Manager as the animation starts at KF100.

Paul
 
Paul, the compression parts really should be start 0 end 200. That's the way I've always done it and it works well for me... :cool:
 
Thanks Bill, I will try that, I thought that because the compression keyframes started at KF100, I should assign them to start in the animation manager at KF100 & not KF0.

Paul
 
I figured that it would work. To be perfectly frank, I'm not even sure why ACES even bothered with a "start" parameter, since sim animations don't work on "partial" animation tracks to begin with!

IOW, every entry will always have zero for the starting key!
 
It's good practice to select all the animated objects in the gear and set the frames 0 - 200 regardless of the actual set frames for any one object.
 
I'll remember to do that. What I you have an animated part except for gear parts that uses less than KF's do you tag it in the animation manager to start 0 & end at 100 or the actual KF's used IE. 0-30.

Paul
 
Paul, in theory the ending frame should be the actual last frame defined. I have found (mostly by mistake) that it doesn't seem to matter all that much as long as it is larger than the actual last defined frame.
 
Paul, in theory the ending frame should be the actual last frame defined. I have found (mostly by mistake) that it doesn't seem to matter all that much as long as it is larger than the actual last defined frame.
Bill, what I like to do for an animated object that, lets say begins motion at frame 30 and ends at frame 100 (and is involved with other objects that will end at frame 200) is move the animation slider to frame 30 then tick one of the X, Y or Z spinners once up then down the object then has not actually moved but a beginning marker is created at 0. Then create my animation through to frame 100. At this point I'll move the slider to frame 200 then tick X, Y, or Z again once up then down creating the end animation marker. So although the animation only occurs during frames 30 -100 the part is animated even though motionless from 0 - 29 and 101 through 200.
 
Last edited:
I use 'Auto' and the dummy key at frame 0 is set for me automatically. Extra keys never hurt anything that I've noticed. :twocents:
 
Here is a good tip. Start key 0 end key 200. But in Gmax for the compression make it so the position you want the gear hanging in the air at key 100 and sitting on the ground at 135 or 140 depending on the stiffness of the CFG settings and fully compressed at key 200.:stirthepo

Having a key a 135 or 140 for sitting on the runway allows you to match other parts that also get animated but may have more movement!
 
Back
Top