Recent content by anuj

  1. anuj

    Create PAPI 2L using AFLT

    Thanks Don. No problem. Appreciate your support on this. Take Care .. Anuj.
  2. anuj

    Create PAPI 2L using AFLT

    Hello Don, Thanks for your time and efforts. I did not found any PAPI2 mdl file in library but have created one and its working fine using new development release. Again appreciating your help as always. Take Care ... Anuj.
  3. anuj

    Create PAPI 2L using AFLT

    Hello Don, I have tried to achieve PAPI 2L (APAPI) using 02 VASI lights keeping glide slope 2.45 and 3.15 but unfortunately its not working. I hope I am doing it correctly (ref.pic. below) Take Care ... Anuj. APAPI Sitting and Angle of Elevation Settings:
  4. anuj

    Create PAPI 2L using AFLT

    Hello Don, Thanks for prompt response. PAPI2 exists eg. Sunnyside Municipal Airport (1S5), it would be great if you can include it in future release. Aside I have just installed mentioned development release and will try to create PAPI2 using 02 single VASI lights. Take Care.. Anuj.
  5. anuj

    Create PAPI 2L using AFLT

    Hello Members, I am bit confused creating PAPI 2L lights using AFLT for my new project. I have tried to use VASI-2 and VASI separately but unable to get one white and one red light in glide slope, while its showing both lights as white or red based on glide slope angles. I have re-checked, my...
  6. anuj

    Increase AFLT Beacon Flash Rate (Resolved)

    Hello Don, Agreed, I somehow missed that part from manual about SUBSTITUTION OF BASE MODELS. Aside I am using MCX just to get object view. Thanks so much for taking the time to help with my project.. All the best. Take care.. Anuj.
  7. anuj

    Increase AFLT Beacon Flash Rate (Resolved)

    Hello Don, After working whole day on my strobes finally every issue got resolved. Somehow I missed xyz settings in types.txt file corresponding with my custom model. Now everything fixed and working fine as I was expecting. Thanks again for your prompt and valuable support. In future it...
  8. anuj

    Increase AFLT Beacon Flash Rate (Resolved)

    Hello Don, Thanks for your suggestion, finally I got flashing strobe with new development release(1100h). I have a small concern with flash attachpoint. I observed that in default and custom objects I am getting flash at ground level while in MCX model attachpoint looks perfect (pls refer...
  9. anuj

    Increase AFLT Beacon Flash Rate (Resolved)

    Hello Don, Appreciate your efforts. Yes, we are working on strobes only. I am using latest development release 1100(d). As per your suggestion I will try to create new one using latest development release. Basically I am looking for REIL (One strobe on each side of the threshold, flashing...
  10. anuj

    Increase AFLT Beacon Flash Rate (Resolved)

    Hello Don, I am sorry for your inconvenience, Perhaps I could not be explained properly the issue. Currently I am using AFLT stock lights only to identify the issue, which I had mentioned in my previous post. I have checked with stock strobe (file:lib_as_reil_strobe_Lights.bgl) but its not...
  11. anuj

    Increase AFLT Beacon Flash Rate (Resolved)

    Hello Don, Thanks for your time and efforts. To isolate issue , I have removed all previous bgl's related with this and created default AFLT strobe as per your previous suggestion and it not working as well. My REIL light setting is unchecked inside ADE as well. I am attaching my custom strobe...
  12. anuj

    Increase AFLT Beacon Flash Rate (Resolved)

    Hello Don, Please find my AFLT library folder as attachment. Take Care ... Anuj
  13. anuj

    Increase AFLT Beacon Flash Rate (Resolved)

    Hello Don, Sorry for delay in response. Unfortunately my PC mother board got dead so I could not be able to share required file for few more days. Take Care.. Anuj
  14. anuj

    Increase AFLT Beacon Flash Rate (Resolved)

    Hello Don, Thanks for reply. Please find attached library folder for your reference. I am using "lib_as_reil_strobe_Lights.bgl" file for this which is located in fs9 directory. I am using AFLT version 1.100(f) Take Care ... Anuj.
  15. anuj

    Increase AFLT Beacon Flash Rate (Resolved)

    Hello Don, Today I have checked creating single strobe as per your suggestions, but unfortunately is not working. I have also tested it keeping ADE light setting (REIL) On and Off both, but results are same. Please advice. Take Care ... Anuj
Top