• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

Animating door

Messages
463
Country
germany
Ok gurus....need some expert advice here...Trying to animate the cockpit doors but I am having trouble getting the door and hinges to line up.
3dsmax1100.jpg

The hinges are located right above the cross bar in the cockpit door window and at the top of the lower window. I have tried numerous ways, like attaching everything to the door, leaving just the cylinder hinge in place, and attaching the mounting bracket to the door....Just for the life of me cannot get the door to animate correctly...
 
Hi,

If you have more than one hinge it might be simpler if you Attach them together, but be sure to save a backup before you do. Then Link all the door stuff to the hinge, and use hairyspin's technique for aligning the pivot point to the hinge. If your hinges are part of the main door, then just link everything else to that part and do the same thing, using the hinge points for your aligning process.

http://www.sim-outhouse.com/sohforu...-Tutorials&highlight=animation+gmax+tutorials

Hope this helps,
 
Hello Nater
1. I do My animations in 3dsmax - but Animations are the same in Gmax - It sounds Like Yourself and I suffer from a similar disorder - " Overcomplicatedness " - And It sounds like You are having problems with Basic Key Frame Animation in Gmax - I assume that You are Familiar with Key Frame Animation in Gmax - if not - there are Plenty of Tutorials - It also sounds like You are having problems getting the door to pivot properly ?? - Let Me try a Little Splainin at You - First - and Foremost - click on Your Door Object - move over to Your Creation Panel and click on the Motion tab - Click on "+Assign Controller" - and switch each controller to linear - Use The "Question Mark Box" at the top of the "Assign Controller Window" - ALL Animations in Fsx/P3d NEED to be with Linear Controllers

2. I hear You talking about Doors and Hinges Ect. - "Overcomplicadidness" - Attach Your Hinges to The Door Object - It is the Door Object that You want to Pivot - the Hinges just go along for the ride. - What You want to do is - (Use the Hierarchy Tab -> Adjust Pivot -> Affect Pivot only) - And Move the Door Pivot - to the front edge of the Door and Rotate it to the angle of the Doors Forward Edge - also Slide it out - to Outer Edge of the Outer Door Panel - this way You do not Rotate the Door into the Fuselage - as it opens - Use Your Rotate Gizmo to Check and Make Sure the Door Pivots Properly - When You get Your Door Motion the way You want it - You can go in and do Your Key Frame Animation and then use the "Aces Tools" - to Assign the Animation for Export.

3. I Usually use a "Helper Dummy" to Anchor and Control My Animations - But that is a Whole Nuther Subject ! What I talk about above should Hopefully get You Started.

Good Luck and let Us know how You make Out - Hope My English is not to American for You.

Johnman
 
Thanks for the tips John...No not to American for me, seeing as I was born and raised in St. Louis....Just live in Germany, because I told myself when I got out of the Army, I was not moving any more. So using your tips, I think I got it pretty damn near close to perfect....I will export to FS and see...
 
This may be what you meant johnman, but once the animation controllers are set to linear as default there's no need to fiddle with them again. There's also some confusion – probably unintentional – between attaching and linking. Attaching an object to another makes it part of the other; linking an object to another only makes it follow the other when it moves or rotates, such as in an animation. As soon as you build more complex animated assemblies, like folding undercarriage, linking becomes the only way to achieve this.
 
Tom, check my showroom thread. I have managed to do it....One thing I did differently than what John suggested is that I moved the pivot point further towards the center of the X axis instead of exactly on the door edge.
 
Attaching - Linking - Either Method will work - I prefer attach as it helps reduce the number of objects in Your Hierarchy - Every Aircraft I have encountered - in 20 Years as a Licensed Aircraft Mechanic A&P - had the Hinges Attached to the door - Linked By the appropriate Hardware !! - Moving the pivot out further than the edge is a Good Idea ! - and Tom - would You take a look at My thread regarding Egg Shaped Prop0 -I would like to get Your opinion ?? Also Tom I was going to soon Ask this - How do You set Your Controllers to Default Linear - Johnman
 
Tidy work, Nater! The link in my post above shows how to set linear controllers to default.
 
Back
Top