• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

Cliffs

R

richard64

Messages
454
Country
wales
Hi, how ya all doin'

ADE and all that working just fine.
Reading this forum reguarly and picking up lots of tips.

However can someone please explain how to get rid of or reduce the "cliff" effect when flattening an area.
If the area is relatively flat anyway it does not show up too much, but if the area is either on a slope or hilly then flattening even a small area produces cliffs.

Is this blending??

Regards
Richard.
 
George is probably the best person to answer this. But you are more or less correct. If the area of the airport is generally not flat then the flatten will cause the surrounding area to be blended in by FSX - and not very well. The way over it is to create some extra sloping flattens from your airport flatten into the surrounding area. The bad news is that ADE 1.22 does not allow sloping polys. The good news is that ADE 1.25 does and this version is in final testing.

It is probably fair to say that if you need to do a lot of this ADE 1.25 will not be the fastest or easiest way to do it. However this functionality will be enhanced over the coming versions.
 
Smashing thanks Jon.

Perhaps George can help but I am happy to wait for 1.25 as I am in no particular at the moment.

Regards.
 
Hello

Presently, you can use SBuilderX to get a gentle slope in place of cliff.
You have your main AB Flatten polygon, horizontal, at airport elevation.
For instance, at the end of runway, you can create an other polygon (rectangle), tagged with AB Flatten, not horizontal, but with different elevations for higher and lower points. So, you have a gentle slope instead of cliff.

Concerning ADE 1.25, will it be possible to use really slopy runways? So far, I created slopy airfields, but afcad / ADE tools can be used only for position, starting places, or parking (all that is at same elevation).

Pierrot - FMEP
 
pierrot1951 said:
Hello

Presently, you can use SBuilderX to get a gentle slope in place of cliff.
You have your main AB Flatten polygon, horizontal, at airport elevation.
For instance, at the end of runway, you can create an other polygon (rectangle), tagged with AB Flatten, not horizontal, but with different elevations for higher and lower points. So, you have a gentle slope instead of cliff.

Concerning ADE 1.25, will it be possible to use really slopy runways? So far, I created slopy airfields, but afcad / ADE tools can be used only for position, starting places, or parking (all that is at same elevation).

Pierrot - FMEP
Click to expand...

No that kind of things need GMax I think. ADE uses the XML based airport code and that does not allow any element to slope
 
Last edited:
I've had luck hand-editing mesh, but it is very slow going. I've always thought maybe a tool like Blackart could automate it, but haven't figured out how to make it work.

scott s.
.
 
You must log in or register to reply here.
Back
Top