• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

FSXA Limiting throttle

euroastar350

Resource contributor
Messages
863
Country
us-delaware
Hi guys,

I am looking for a solution to a small issue I am having. Whenever turning on the fuel valves in my helicopter, the throttles jump from 0-100 which should not occur at all. What I want to do is to have the throttle(s) stay at 0 when the fuel valves are turned on. This is a known bug within FS2002/2004/FSX and I know there are workarounds to this issue. Of course I am using the mixture variable instead of throttle or propeller and it works quite well as a throttle in the helicopter. Any help is greatly appreciated.

Code:
<PartInfo>
    <Name>B222_eng1_throttle_grip</Name>
    <AnimLength>100</AnimLength>
    <Animation>
      <Parameter>
        <Code>
          (A:general eng mixture lever position:2,percent)
        </Code>
      </Parameter>
    </Animation>
    <MouseRect>
      <Cursor>Hand</Cursor>
      <TooltipText>Throttle (%((A:general eng mixture lever position:2,percent) s0)%{if}%(l0 abs)%!d!%% %(l0 0 &gt;))</TooltipText>
      <MouseFlags>LeftSingle+RightSingle+Wheel</MouseFlags>
      <CallbackCode>
        (M:Event) 'LeftSingle' scmi ! (M:Event) 'WheelUp' scmi ! or if{
        (A:general eng mixture lever position:2,percent) int 4 &gt;
        (A:general eng mixture lever position:2,percent) int 4 &lt; || (L:counteridleengL, enum) 0 &gt; ||
        if{ (A:general eng mixture lever position:2,percent) -- 163.84 * (&gt;K:MIXTURE2_SET) }
        <!-- Calculate timer idle stop -->
        30 (&gt;L:timeridlestop, enum)
        (L:counteridleengL, enum) 0 &gt; if{ (L:counteridleengL, enum) -- (&gt;L:counteridleengL, enum) }
        }
        (M:Event) 'RightSingle' scmi ! (M:Event) 'WheelDown' scmi ! or if{
        (A:general eng mixture lever position:2,percent) ++ 163.84 * (&gt;K:MIXTURE2_SET)
        }
      </CallbackCode>
    </MouseRect>
</PartInfo>
 
Issue a (>K:THROTTLE_CUT) command when the fuel valves are toggled?

Also, what's with the timer? Do you want the switch to return to the neutral position?
 
How would I issue the command? Would I replace what I have above with what you posted?

Also, the timer is part of the idle release switch. It's a 3 position switch that allows the throttles to roll past the 5 percent tick to cutoff. So this mean no keyboard shortcuts are built into this helicopter.
 
I would assume something like:

Code:
if{ (A:general eng mixture lever position:2,percent) -- 163.84 * (&gt;K:MIXTURE2_SET) (>K:THROTTLE_CUT) }

and the same in the other similar line.
 
How do you know the throttle is at 100%? The stock tooltip for the collective has the two parameters it reads deliberately reversed.
"Collective Lever (Rotor Pitch - %((A:GENERAL ENG THROTTLE LEVER POSITION:1, percent))%!d!%%, Throttle - %((A:GENERAL ENG PROPELLER LEVER POSITION:1, percent))%!d!%%) "
This is done because the regular throttle movement is applied as a collective, ie it affects rotor pitch. The "throttle" function comes from Prop pitch and you can see it animate the throttle twist grip in the stock Bell.
So, if you want to close the throttle use the prop pitch control.
Roy
 
Ingenious... I never thought of effecting Turbine power with Mixture... I'll have to remember this for a cool turbine low throttle effect...
 
I think the effect of mixture on effective turbine output is rather low, BUT having the mixture lever below 25% will make a turbine refuse to start in FSX. So every turbine aircraft should have an initialization gauge that checks for mixture lever settings and accoringly adjusts them if they are outside of the permissible range.
 
For a helo turbine, which is probably what we are talking about here. I say probably because this variant of the Bell model has turboprops and propeller characteristics. So, lets just say a pure helo turbine is only affected by mixture in that it acts as an on/off valve with something like 2.5% or less being shut-off. Same is true for turbojet/turbofan models.
On the other hand a turboprop engine has reduced RPM and torque with mixture below about 15%. It is implemented by mixture controls being condition levers that govern ground idle or flight idle.
In flight idle there is full torque and the beast tries to get away when taxying. If you select ground idle by moving mixture percent to below about 15% that is when RPM and torque are reduced.
Real helo turbines also have ground idle and flight idle regimes, but that can only be simulated by using SimConnect.
Roy
 
When I released my Lear, quite a few had issues (who were using other planes cold and dark start points) where one engine consumed less fuel, had less thrust, couldnt be started, etc. We traced it to the customers using a planes cold and dark that was a single engine petrol. This meant their mixture was zero at startup, causing inability to start the turbine, or if they could start it, that engine ran very poorly, the fuel burns between the two were far off.

For creating a realism setting, one could make an 'overheat' simulated state (having learned about this) where one could lower the mixture rates, perhaps in increments over a short period of time where the turbines lose power from overheating.

Another cool feature would be the semi-stall you get from slamming the throttles forward too fast (on the older Lears) which caused the turbines to stammer for a moment. That might be cool to get that to work, but you would need to calculate a throttle slamm, like from 30% power and less, going to instant 95% power or more in a half second. (eeks... how might that be done without a code flood??)
 
I think the effect of mixture on effective turbine output is rather low, BUT having the mixture lever below 25% will make a turbine refuse to start in FSX. So every turbine aircraft should have an initialization gauge that checks for mixture lever settings and accoringly adjusts them if they are outside of the permissible range.

Very good idea...
 
Another cool feature would be the semi-stall you get from slamming the throttles forward too fast (on the older Lears) which caused the turbines to stammer for a moment. That might be cool to get that to work, but you would need to calculate a throttle slamm, like from 30% power and less, going to instant 95% power or more in a half second. (eeks... how might that be done without a code flood??)

Code:
(P:ABSOLUTE TIME, seconds) (G:Var2) - 1 &gt;
  if{ (P:ABSOLUTE TIME, seconds) (>G:Var2)
  (A:GENERAL ENG THROTTLE LEVER POSITION:1,percent) (>G:Var3)
  }
  (A:GENERAL ENG THROTTLE LEVER POSITION:1,percent) (G:Var3) - (>L:Delta_Throttle,number)

(L:Delta_Throttle,number) 10 &gt;
(A:GENERAL ENG MIXTURE LEVER POSITION:1, percent) 26 &gt; and
if{ 26 163.83 * (>K:MIXTURE1_SET)  }

(L:Delta_Throttle,number) 10 &lt;
(A:GENERAL ENG MIXTURE LEVER POSITION:1, percent) 99 &lt; and
if{ 100 163.83 * (>K:MIXTURE1_SET)  }

Might require adjustment for the throttle limit, but I guess 10% per second should do for a start.
 
Another cool feature would be the semi-stall you get from slamming the throttles forward too fast (on the older Lears) which caused the turbines to stammer for a moment. That might be cool to get that to work, but you would need to calculate a throttle slamm, like from 30% power and less, going to instant 95% power or more in a half second. (eeks... how might that be done without a code flood??)

Isn't that controlled by table 1505. When I do a slam test for the RR Conways the interval is correctly just over 6 seconds. I'll have to do some test with the mixture lever to see if it does have an effect on EGT.
 
There appears to be some confusion here about "turbine" engines.
In FSXA/P3D there are four varieties of turbine engine.

1. There are turbojet/turbofan engines.
The simulator treats both as the same. Mixture lever less than 1% will stop the engine AND prevent it from starting. Above 1% mixture has no effect on these engines. The Lear is a turbofan

2. There are turboprop engines.
Here the mixture is treated as a conditioner lever. Below 1% fuel is cut-off, between 1% and about 33% the engine (with throttle shut) is at ground idle, torque is at about 10%. Above 33% the torque increases and at 100% mixture/conditioner it is at 25%. It will start once the mixture/conditioner exceeds 1%. KingAir is a turboprop.

3. There are two varieties of Helo-turbine. The old "legacy" version is found as the stock Bell 206.
In the Bell, mixture above about 0.4% has no effect on the engine.
Mixture at 0% also shuts down the general eng fuel valve:1 and stops the engine, putting the fuel valve on and taking the mixture off the zero value causes it to run again.

4 The fourth variety is the EH-101 type helo turbine.
Mixture lever less than 1% will stop the engine AND prevent it from starting. Above 1% mixture has no effect on these engines.

During an autostart (CTRL E) mixture will initially be put to zero then increased to give combustion at the appropriate instant in the start cycle.

In general you can think of the Mixture being like a HP cock for turbines other than turboprops, it is on the engine side of the fuel valves which act like an LP cock.
The airfile has different engine content for the four turbine types, as does the aircraft.cfg.

Roy
 
Last edited:
Back
Top