• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

AI traffic

Messages
224
Country
sweden
Hi , long time no ...........!

With some help from a good friend we have created 3 Pa28 which do
fly on ESOW in realty . I can't make them to taxi out for departure
because when the time is right they just vanish.

They do fly on other airports with the same size of the parking spot.
The big guys like 737,MD80 do fly.

As always I look forward for your help .

Best regards:

Chico

P.S. This goes only for FS9. D.S.
 
Hi,

You do not have a valid route for them from the parking spot to the runway assigned by ATC. If using AFCAD or ADE, use the Fault Finder to see if you have any unconnected nodes.

Also, you must have the taxiway system connect to a black runway line, with the correct runway label.

There is a possibility that you have created a small runway for other purposes (crosswind technique, etc.) - make sure these are not assigned by ATC (move them far away, etc.).
 
Hi Tom, thank's for your reply :wizard:

I do have a valid route from the parking spot as my beloved CV340 is using it .
I have ok from fault finder in ADE9 and my taxiway system is connected with
the black line on the runway.
And I have a Jack Daniels waiting for you if you can solve this minor problem.

Take care:

Chico
 
Glad to hear that the 340 is doing well. :)

Perhaps the GA aircraft are being assigned to another runway. Is there more than one runway at this airport? Is that other runway short?

Or is the PA28 parking closer to a different runway than the CV340 parking spot?
 
Tom,

I checked this airport as well in FS9 a while ago and could not find any faults either.
The only difference between Floda's airport and mine was the additional (short) grass runway without any connections to the taxiway network.
My airport showed AI as it should, his did not (as they disappeared upon having landed) and no additional comms either for the grass runway.

Roby
 
Keep in mind that GA aircraft might be assigned to the small grass runway, even if not connected to the taxiways, no start locations, etc. If that happens, poof!
 
Hi Tom !

Thank you again for your reply. The Pa 28 do now taxi and take of from the grass runway
thank's to Roby. Your last suggestion would have done it as well.

I am trying to do the same trick in FSX but so far no good result.

Best regards:

Chico
 
Apparently in FSX the grass runway has to have a minimum length of 800m otherwise it will be ignored.
 
Hoi Roby. :wizard:

You are wright as usual, The grass strip on ESOW is 800m. Don't know why
I made it 716 m. Now there is a lot of action going on.

Dank U Wel.

Chico
 
Back
Top