• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

FS2004 Flap Designation

Messages
292
Country
unitedkingdom
Hi, the model I am currently creating has 2 flaps on each wing which are keyframe animated, the part name for a single keyframed flap is L_Flap_Key or R_Flap_Key, so because I have 2, do I name them L_Flap_01_Key & L_Flap_02_Key or L_Flap_Key_01 & L_Flap_Key_02.

Thanks in advance.
 
Always put the variation numbers at the very end. L_Flap_Key_01.

Hope this helps,
 
Thanks Tom, I thought I had better make sure or I would be pulling my hair out trying to find the reason the flaps weren't working.
 
It's a good thing I took a second look at the thread title and notice this is concerning FS2004 or else I would have hugely embarrassed myself... :rotfl:
 
The first few animations, compile a model and make sure they are working in the sim. :)

Flap_Key isn't a proper FSX animation?
 
Flap_Key isn't a proper FSX animation?
Well, yes and no, actually. What I was referring to is that for FSX and P3, specific part names are not required, since all animations are created via the Animation Tool, which uses names pre-defined in the modeldef.xml script file.
  • l_flap_key
  • l_flap_neg_key
  • l_flap_percent_key
  • l_flap_neg_percent_key
  • l_lead_edge_flap_percent_key
These animation script names that may be selected for use could be applied to a part named "Fred" and it would make no difference at all in the end results.
 
So, does that mean that a model compiled for FS2004 in Gmax with flap keyframe animations, the flap animation will not work if the model is used in FSX?
 
So, does that mean that a model compiled for FS2004 in Gmax with flap keyframe animations, the flap animation will not work if the model is used in FSX?
Yes, they will work! FS9 a/c will continue to work as designed in FSX because they included the backwards-compatibility code in FSX just for that reason...
 
I've worked too long in FS9, so for my (few) FSX models I also use the part names as I did in FS9. :)
 
Even though my model is far from finished, I decided to compile a model to test the flap animation, the aircraft I am modelling has 3 flap settings 10 degrees - take-off, 20 degrees - approach & 30 degrees - landing, it has two fowler flap segments on each wing, the inner flap deploying to a max 30 degrees & the outer flap deploying to a max of 20 degrees, so I set the flap settings in aircraft.cfg as follows:
[flaps.0]
type = 1 // 1 - tail, 2 - lead
span-outboard = 0.41 // 0.0 .. 1.0
extending-time = 5 // seconds
flaps-position.0 = 0 // degrees
flaps-position.1 = 10 // degrees
flaps-position.2 = 20 // degrees
flaps-position.3 = 20
damaging-speed = 152 // KIAS
blowout-speed = 250 // KIAS
[flaps.1]
type = 1 // 1 - tail, 2 - lead
span-outboard = 0.41 // 0.0 .. 1.0
extending-time = 5 // seconds
flaps-position.0 = 0 // degrees
flaps-position.1 = 10 // degrees
flaps-position.2 = 20 // degrees
flaps-position.3 = 30
damaging-speed = 152 // KIAS
blowout-speed = 250 // KIAS

As I am using an FS9 template air file (Turboprop), I set the flap positions No. to 4.

However, the flaps work OK in FS9 but in FSX they only deploy to 2 positions, 3 if you include the neutral position, with a maximum angle of about 20 degrees, I don't know the reason for this, I hope someone knows why.
 
Maybe FSX doesn't like two positions with the same setting (20 degrees). Try deleting flap.0's flaps-position.3?
 
Back
Top