• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

FSX Reference datum position

Messages
235
Country
ca-ontario
I need to confirm that I got my information straight in regards to reference datum and Flight Simulator center point.

Assumption 1; since I am working on a boat, my “Flight Simulator Center” should be located at the center of gravity of the boat.
Assumption 2; Aircrafts (in my case boat) reference datum is the location of the 0,0,0 point that was used in Gmax while creating the model.

If the above assumptions are correct, since I am building my model with the 0,0,0 in Gmax located at the center of gravity of the boat and at the waterline , this is what I should have in my sim.cfg :

reference_datum_position = 0.0, 0.0, 0.0
empty_weight_CG_position = 0.0, 0.0, 0.0

Presently I have the following;

reference_datum_position = 28.20, 0, 0.0
empty_weight_CG_position = -28.20, 0, 0.0

Although I may need to reassess the empty weight CG as I will need to reexamine my boat plans as to vertical position of the center of gravity, if it is given.

Reading documentation for the aircraft.cfg, they make reference to “defined reference datum” in one location and “aircraft datum reference point” in other placed. Are these the same or is the first one the FS center point and the second the model 0,0,0?
In my case, these might be the same, but I like to be clear that I am interpreting the wording correctly.

Michel E Paquette
 
The answer is that all other measured positions are based on the reference_datum_position, which is why your empty_weight_CG_position is "offset -28.20" from the reference_datum_position.

In actual practice, most modelers do not bother with the reference_datum_position at all, and set both ref_dat and empty_weight_CG to the model's center origin position of 0,0,0...

However, if the modeler has the builder's data, it is to their advantage to set the ref_datum according to the builder's blueprint, so that all other measurements may be entered based on real-world data.

One other advantage of setting the ref_datum to for example, the 'bowsprit' of your boat is that all offsets aft of that position are negative. In other words, you won't have to use a positive value for the bow light, and a negative value for the stern light! Instead, you can use the "tape measure tool" in your modeling program to determine the precise coordinates for everything you need to place via the "aircraft.cfg" or "sim.cfg" file.
 
Bill
The values that I presently have in my sim.cfg file that I show above, are values that I put in when I started on my project. In a way, I am wandering if I gat them right.
As mentioned, When I started to detail my boat on Gmax, I set it up to have my CG at 0,0,0 on Gmax. I have no problem in using (+) for all items forward of CG, and (-) for all items behind the CG.
In this case would I revise my reference datum position to 0,0,0 and CG at 0,0,0? Then all dimension for my cfg file would be from CG and not the bow, is this correct?

When you talk about "builders data" for an airplane, are all dimensions given from the nose of the plane, therefore the reason for using the nose as the ref datum?
Because my boat plans are not detailed in such a manner. The boat is set up into 16 "stations" at 33" apart and all dimension are relative to those station and the centerline. Therefore for me it was juast as easy to set my 0,0,0 on Gmax to the CG.
 
One small correction. I just looked at my plans and what they give me is "center of buoyancy", not "center of gravity".

Michel
 
If the centre of gravity is at a different place from the centre of buoyancy a boat will list or even capsize, whereas an aircraft will climb, dive or roll when CoG and centre of lift differ laterally or in longitude. Strictly speaking, the centre of buoyancy ought to be directly above the CoG and an aircraft's centre of lift ought to be directly above its CoG (for straight and level flight): how much above will govern the general stability of either.
 
When you talk about "builders data" for an airplane, are all dimensions given from the nose of the plane, therefore the reason for using the nose as the ref datum?
Yes, although commonly the ref_datum for aircraft builder's data sets an arbitrary point somewhere ahead of the aircraft's nose (or whatever part of the aircraft's anatomy is furthest forward).

In practice, for modelers who aren't as anal-retentive as perhaps I am, making the model's origin, the ref_datum, and the empty_weight_CG points congruent is the simplest approach to take. :rotfl:
 
Thank you.
I think it is also the simplest way, to have the model's ref_datum at the CoG.
Since I have made my model with origin at CoB (as hairyspin says, CoB should be = CoG), I am changing my cfg file to the following:

reference_datum_position = 0.0, 0.0, 0.0
empty_weight_CG_position = 0.0, 0.0, 0.0

And all my location for contact points, and loading will be from my CoG.

Michel
 
Well, not to be overly pedantic, the contact point locations are still going to be referenced from the reference_datum_position, but since it is precisely congruent with the CoG point there's no practical difference... :teacher:
 
Back
Top