• Which the release of FS2020 we see an explosition of activity on the forun and of course we are very happy to see this. But having all questions about FS2020 in one forum becomes a bit messy. So therefore we would like to ask you all to use the following guidelines when posting your questions:

    • Tag FS2020 specific questions with the MSFS2020 tag.
    • Questions about making 3D assets can be posted in the 3D asset design forum. Either post them in the subforum of the modelling tool you use or in the general forum if they are general.
    • Questions about aircraft design can be posted in the Aircraft design forum
    • Questions about airport design can be posted in the FS2020 airport design forum. Once airport development tools have been updated for FS2020 you can post tool speciifc questions in the subforums of those tools as well of course.
    • Questions about terrain design can be posted in the FS2020 terrain design forum.
    • Questions about SimConnect can be posted in the SimConnect forum.

    Any other question that is not specific to an aspect of development or tool can be posted in the General chat forum.

    By following these guidelines we make sure that the forums remain easy to read for everybody and also that the right people can find your post to answer it.

FS2004 Texturing Question

Messages
292
Country
unitedkingdom
I have tried searching for an answer to my problem, but without success, what I would like to know is how to texture an aircraft fuselage using 2 texture sheets, one for the left side & one for the right, all the fuselages of the models I have made in the past have been put on to a single texture sheet which is easy, just UVW map each side separately, but I am confused about how I go about UVW mapping 4 or 5 different sections of the fuselage, the 5th is the belly. The only way as far as I can see of doing this is to split the fuselage into two separate parts (left & right), but this would end up looking messy.

The reason for wanting to use two texture sheets is because I want to put the front sections of the fuselage in the top part of the texture sheets & the rear section on the bottom so I can have higher resolution textures from the 1024x1024 max texture size.

Any advice will be much appreciated.

Paul
 
Hey Paul,

There are several ways, some sophisticated, some very basic. I'll tell you a basic route, but its crude.

Basically you want a 'multi-material'. This is two textures for one part. So, you create 'two' textures, one with the first half of the texture, and the second material with second half.

Next apply the first material to your fuselage. Then, split the fuselage at the seam where the textures meet. If you need to, 'slice' the fusealge so the border is perfect along an edge.

Now apply the 'second' Material to the fuselage

Next, Map both and get them perfect so they match up 100% right on.

Now.... You must 'Attach' the first half of the fuselage to the second half. You will be asked if you want to keep that material and you want to so it will automatically create a Multi-Material for you. (There are like 4 questions on this scene when you attach the parts, I forget the correct answer, but you'll see when you make the right decision, as they will retain both of their proper mappings/textures).

Now, just weld the Vertices back together along the seam that they were broken at, smooth to get rid of the edge/seam (if it still shows up after welding) and you are done.



That is the 'basic' and crude way. ;)
 
Thanks for the advice, this sounds harder than I thought it would be, so I create two textures, lets say Fuse L & Fuse R & then I add the Fuse L texture to the whole fuselage without using the UVW mapping, I then divide the fuselage into left & right, so now I have a fuselage L & fuselage R & I apply the Fuse R texture to fuselage R. Do I now map them in the position I want them to appear on the textures? Can I now export them into LithUnwrap? How can I weld the two fuselage halves together after I have mapped them?
 
Thanks again for the help with this, I think I have cracked it, I split the parts into left & right sides & textured, UVW mapped the fuselage sides as I want them to appear on the textures & then it came to the joining of the left & right fuselage sides, as I have not done this before I didn't know how to go about this so I added an edit mesh to each fuselage part stack, I didn't know if this could be added after mapping, but it worked & I attached both fuselage sides & welded.

Gmax is a wonderful tool, but only if you know how to use it!!!! I still have lots to learn about Gmax & it's the helpful people here at Fsdeveloper that help others to make it so much easier to progress with this addictive hobby!!
 
Congrats, Paul!

I just collapse the stack, then attach and weld. Then you can add another UVW Unwrap and re-edit things if needed.

Yes, Gmax is awesome, and quite a bit to learn, but at least with the basics, you can do much.

Try roaming through YouTube for Gmax tutorials. Also, early versions of Max, like Max 7 as the early versions of Max are basically the same as Gmax, except Gmax doesnt have Rendering.
 
I did encounter a problem when attaching the two fuselage sides, I selected the wrong option regarding the multi materials & ended up with the material ID's messed up so when I did a test model export I got an error message, but I sorted that out & all is OK. I didn't realise that it was possible to collapse the stack after UVW mapping, I thought I would loose the mapping.

Thanks again, now I know a little bit more about Gmax, it will make modelling a bit easier, I can't wait to learn more so I will seek out some Gmax tutorials on YouTube.
 
Ahh soo... Roger. Just to let you know, first, always back up and create 'next level up' saves (you probably do that already). Second, experiment a LOT! Always play around with how things work so you get an idea, but when you do, always create a new level up, or even rename it like 'my plane 443 experiment 1' so that you can know where you are and what you are doing.

Second, when you collapse a stack, especially on a UVW Map, you simply lock it in. You can always add another UVW Unwrap later and 'edit' your mappings. That is a cool feature. Always able to make adjustments to maps without having to redo the entire thing, (like if you forget a small little area, just remap that little area instead of the entire thing), then collapse the stack again once you are done.

Alot of people like to keep their stacks. They 1. increase amount of memory used to the point that it can cause a malfunction during export, requring you to collapse some stacks so you can make a test export, and 2. can disable you from making certain changes to the part(s). Keeping the part 'collapsed' makes it 'locked in and pure' and not a floating variable mess. (Thats my own opinion and others will defend keeping their stacks and thats ok, that is their direction they use in making models).
 
Also, did you know you can edit 'just a set of polygons' on a part? (I love doing this often). If you have an area that isnt right, select the Polygons then select/add UVW Unwrap and make the changes to those Polys only, save, collapse, done!

Great for doing really difficult parts that would be very sophisticated to map in certain ways. Just remember, the 'first' time you map something, you 'must' add a UVW Map to it, a Plannar, be it a cylinder or flat Plannar, etc. It must be Mapped (the whole thing) before you can start doing 'spot' touchup edits later down the road. All Polygons that are mapped must have a Plannar applied to them or it will have many problems and possibly not export.

Example, if you were going to map a seat (can be difficult), first add a side 'Plannar' UVW Map to the whole thing. Then carefully adjust the side in UVW Unwrap. Save, collapse. Now, choose your top zones in Polygon mode, add UVW Map and UVW Unwrap to those, edit, save, collapse, done. Repeat till you are finished.

This can really speed up and streamline mapping.
 
BTW, a slightly simpler method of multi-mapping:

1. Click the red ball at the top (Material Editor), create a new Material (click the New button), and choose Multi-Material.
2. In the first submaterial, add your first texture bitmap file in the Diffuse slot. Click the blue and white cube.
3. In the second submaterial, add your second texture bitmap file. Click the blue and white cube.
4. Select your fuselage part, and click Apply in the Material Editor.
5. Now your fuselage will need to be mapped, using UVW Map and UVW Unwrap. The entire fuselage will use the bitmap in submaterial 1. That's OK, we'll do the other side next. Be sure to do the *entire* fuselage, even if the other side is backwards.
6. Add an Edit Mesh (Edit Poly) modifier to the stack, and go to Polygon subobject mode (click the the little black + next to the modifier name).
7. Select all the polygons that should instead be textured using the submaterial 2 bitmap.
6. In the listing on the right, scroll down to Surface Properties.
7. You will see a heading named Material, with ID displayed at the left (next to a box with the number 1 in it). Change that number to 2.

Now the selected polygons will have an ID of 2 and use submaterial 2 , but the unselected ones will still have an ID of 1 and use our previous submaterial 1.

8. Add a UVW Unwrap to the stack, and select bitmap #2 from the drop down list in the upper right. It may not be called #2 - that's OK.
9. Map the other side of the fuselage - depending on your texture arrangement, it may be quite easy. I usually only have to select all the vertices, flip them, and move them (all) until they are perfectly aligned along the second bitmap.

This way both sides of the fuselage will have exactly the same mapping and should align perfectly.

Hope this helps,
 
Back
Top